Replacing Sandfilter Media

- every 4 years or so it's time to replace the sand in the filter, and this is how you do it: -                                                                                  

  • Switch the pump to ‘Off’ and close all Valves
  • Remove the lid of the filter and, immediately underneath, you will seea plastic fitting that looks like a large-hole watering-can sprinkler rose
  • This is the ‘diffuser’ and must be removed from the filter by gently twisting and pulling, to allow access to the inside of the filter
  • Notes: -Some filters incorporate a screw-thread fitting to attach the diffuser. Some filters have a specially shaped underside to the filter lid which acts as a diffuser, so don’t worry if you don’t have a separate diffuser
  • Normally there is air relief tube extending up through one of the holes in the diffuser - this tube allows pressure to be balanced between the top and bottom halves of the filter - take care not to damage the tube or breather-cap which is fitted to the top of the tube
  • Now you can get at the filter media for removal
  • Wear rubber gloves and use an empty can or plastic jug to scoop out the sand
  • Put the removed sand into a bucket for later dumping
  • Take care not to damage the plumbing inside - feel your way until you are familiar with the layout of components
  • Once most of the media has been removed unscrew the collectors from the central hub of the lateral assembly for inspection and possible later renewal
  • Use a little residual media and water to scour the inside of the filter vessel and then remove the remainder of the media
  • Wash the top and outside of the filter and the screw threads of the collector hub with a hose to remove any grains of media
  • Check, and if necessary change, the 8 or more ‘collectors’ or ‘laterals’ in the lateral assembly, which are fitted like spokes on a central hub at the bottom of the filter; buy them at your local pool-shop but take an old one along with you for comparison because there are several sizesSanmd-filter Lateral Array Collector

A typical collector from the lateral assembly

Replenishing the filter media: -

  • Consider changing the media to ZeoclereZeoclere - it's a little more expensive than Silex but filters much better and last for 10+ years - far longer than Silex, and also srtrips ammonia and dissolved heavy metals from the pool.
  • There may be an information label, on the outer surface of the filter, which details the filter Make/Model and the quantity of Silex within it
  • Very often this is missing or illegible and you will have to guess how much you need, using the amount  removed as a rough guide
  • Note: ZeoclereZeoclere is approximately 80% the density of sand so you need only 80%-by-weight: - thus if your filter contains 100Kg of Silex you need only 80Kg of Zeoclere to re-fill the filter
  • Place a can or plastic jug over the upward-facing opening to the inlet pipe to avoid filling it with the new media
  • Pour new media into the filter and add water to help it to settle
  • The correct level is to the top of the horizontal section of the upper pipe. (It’s simple once you see the inside of a sand-filter)
  • If you add too much media the level will adjust automatically during routine back-washing, when the excess will be gradually flushed out
  • Rinse any grains of filter media from the filter lid, nuts and caps, or lid screw thread as applicable
  • Examine the filter lid ‘O’ ring and replace if it is damaged in any way
  • Smear the ‘O’ ring with a thin coating of silicon grease or Vaseline and thoroughly clean the underside of the filter lid and the filter seating
  • Fill the filter with water, replace the lid and tighten down carefully
  • Set the Rotary Valve to ‘Backwash’ and open the Bottom Drain and Waste valves
  • Backwash the media for several minutes to remove dust, and then Rinse as normal
  • If you are re-filling with Zeolite you should backwash each bag thoroughly before putting the next bag in - it’s more time-consuming but the results are worth it
  • Check for leaks during the 'Rinse' process and rectify them
  • Repeat the cycle until the water runs clear
  • Set all the Pump-room Valves and switches to ‘Filtration

Congratulations! - you have just renewed the filter media and collectors!  

Now go and rest your back for three days

The old media should not be used for building purposes, in a garden or in a sand-pit 

 

We supply all plant and equipment featured on this website. All our work is Guaranteed; Parts and Labour

 

For free and unbiased advice, a site visit or no-obligation Quotation*, please make initial enquiries by email. Tell us a little about your pool problem and include a daytime phone number. Thanks, we look forward to meeting you soon

 

Note: - Please contact our recommended pool professionals for supply and installation of all pool-related services: - 

Costa del Sol - This email address is being protected from spambots. You need JavaScript enabled to view it.

Nerja area - This email address is being protected from spambots. You need JavaScript enabled to view it.

 

*We only offer Quotations: - a fixed, agreed price that cannot, and will not, be increased. We do not give 'estimates', as an estimate offers the client no guarantee of final price

 

Share this website with other Pool Owners and Users,  encourage them to read about Pool Safety, learn CPR and help them to save lives, time and money. Please help us to make every pool a safer place - by sharing this information we can cut the number of pool accidents and deaths.  Please also see our FacebookFacebook page

 

 

Ken Walker - MyPoolGuru©